Category: Accessories for ATyS

CONTROL RELAYS-ATyS C20/C30/C40-SOCOMEC

Control Relays for ATyS C20/C30/C40 The solution for Power and control separation Genset/Genset applications Strong points Auxiliary power supply Moduar device Extended compatibility of use Conformity to standards IEC 61010-1 IEC 61000-4-X IEC 60068-2-X Function ATyS C20/C30/C40 are modular control…

ENCLOSED SOLUTIONS-ATyS-SOCOMEC

General Characteristics ATyS d and ATys p Adapted to mechanical risk and dust hazard. IP rating: IP54 Colour: RAL 7035. Connecting the cables: upstream or downstream up to 250A then downstream only. The auxiliary contacts are wired to terminal blocks.…

MOTORISATION MODULE – ATyS – SOCOMEC

Moterisation Module for ATyS Range- ATys r, d, g, t, and p The motor units of the ATyS r, d, t, g and p be easy to replace in case there is a problem, even when on-load. Rating (A) Reference…

ATyS p FRONT PANEL

Front panel for ATyS p This front panel is used, for the ATyS p only, if source 2 is connected to unit I and source 1 is connected to unit II. Positions I and II are reversed on the front…

DOUBLE POWER SUPPLY – DPS

Double Power Supply – DPS – for ATyS UseAllows an ATyS r or to be supplied by two 230 VAC, 50/60 Hz networks. Input. The input is considered “active” from 200 VAC. Maximun voltage: 288 VAC Internal protection: each input…

REMOTE INTERFACES AND CONNECTING CABLE – ATyS-SOCOMEC

Remote Interfaces for ATyS Range – ATyS r,d,t,g, and p. from 125 to 3200A UseTo remotely display source availability and position indication typically used on the front of a panel when the product is enclosed. Interfaces are powered from ATyS…

KEY HANDLE INTERLOCKING SYSTEM-ATyS-SOCOMEC

Key Handle Interlocking System for ATyS UseWith the product in manual mode, it enables locking in position 0 using a RONIS EL11AP lock (factory fitted). As standard, locking in position 0. With the 3 position padlocking accessory: Key interlocking in…

3 POSITION PADLOCKING (I-0-II)-ATyS-SOCOMEC

3 Position Padlocking (I-0-II) for ATys UseEnables the product to be padlocked in position 0,I and II (factory fitted). Rating (A) Frame size Reference 125…630 B3…B5 9599 0003 800…3200 B6…B8 9599 0004

MOUNTING SPACERS FOR ATyS-SOCOMEC

Mounting Spacers for ATys UseIncreases the distance between the rear power terminals and backplate by 1 cm. This accessory may also be used to replace the original muonting spacers. Rating (A) Frame size Description of accessories Reference 125…630 B3…B5 1…

AUXILIARY CONTACT FOR ATyS-SOCOMEC

Auxiliary Contact for ATyS Usepre-break and signalling of positions I and II: each reference provides 1NO/NC auxiliary contact for positions I and II. Possibility to install up to 2 auxiliary contacts for each position. Low level AC: contact us. ATyS…

VOLTAGE RELAY FOR ATyS-COSOMEC

Voltage Relay for ATyS r,ATyS d,ATyS t,ATyS g,ATyS p : From 125 to 3200A UseThe DS is a voltage relay for monitoring a single power supply. If it detects a fault in the source, the default relay cintact closes. Rating…

VOLTAGE TAPPING AND POWER SUPPLY KIT FOR ATyS

Voltage tapping and power supply kit for ATyS r,ATyS d,ATyS t,ATyS g,ATyS p : From 125 to 3200A UseFor power supply and voltage measurement ( 4wire, three-phase) for the ATyS t,g, and p. Rounting of the conductors is controlled, which…

SOLID NEUTRAL FOR ATyS

UseThe solid neutral kit provides connection between the incoming and outgoing neutrals with no disconnection during transfer.

COPPER BAR CONNECTION PIECES-ATyS-SOCOMEC

Copper bar connection pieces for ATyS-SOCOMEC UseFor ratings 2000 to 3200A Enables: Flat connection: the connection pieces provide a link between the two power terminals of the same pole (Fig.1) Edgewise connection: the connection pieces provide link between the two…

ATyS RANGE- ACCESSORIES-SOCOMEC

Accessories for ATyS r , ATyS d , ATyS t , ATyS g , ATyS p from 125 to 3200A Terminal shrouds UseIP2X protection against direct contact with terminals or connecting part. Advantages Perforations allow remote thermographic inspection without the…