SCHNEIDER remote control source changeover, Transferpact, ACP plate and UA controller, 220 VAC to 240 VAC 50/60 Hz
29472
รายละเอียด
It is a remote controlled source changeover system for Compact NSX, Compact NS and Masterpact devices. It is composed of an ACP plate and of an automatic UA controller. This ACP provides in a single unit the protection of the controller, the control and the connection to the devices. The UA controller is used to create a source-changeover transfer from one source to another depending on the presence of voltage UN on the “Normal” source. UA controller integrates also the start up of an engine generator set, the shedding and reconnection of non-priority circuits, the transfer to the “Replacement” source if one of the phases on the “Normal” source fails. The control voltage is from 220VAC to 240VAC 50/60Hz.
ข้อมูลจำเพาะ
| Range of product | NSX100…250 Compact NS100…630 MasterPact NW MasterPact NT NSX400…630 Compact NS630b…1600 |
|---|---|
| Product or component type | Interface and control unit |
| Accessory / separate part category | Interlocking accessory |
| Range compatibility | ComPact ComPact NS circuit breaker ComPact ComPact NSX circuit breaker Masterpact MasterPact NT circuit breaker Masterpact MasterPact NW circuit breaker |
| Device short name | ACP + UA |
| [Us] rated supply voltage | 220…240 V AC at 50/60 Hz |
| Operating mode | Automatic operation Forced operation on normal source Stop (both normal and replacement source off) Forced operation on replacement source |
|---|---|
| Interlocked device | MasterPact NT NSX400…630 MasterPact NW NSX100…250 Compact NS100…630 Compact NS630b…1600 |
| Selection modes | Circuit breaker on R Circuit breaker on N |
| Test function | By pressing the test button on the front of the controller |
| Complementary function | Voluntary transfer to replacement source (e.g. energy management commands) Forced normal source if replacement source not operational during peak-tariff Selection of type of normal source (single-phase or three-phase) Setting of maximum startup time for the replacement source Additional contact: transfer to replacement source only if contact is closed |
| Local signalling | On Off Fault trip |
| Input type | Contacts customer voluntary order to transfer to source R |
| Output type | Contacts customer: indication of operation in automatic or stop mode |
| [Ith] conventional free air thermal current | 8 A |
| [Ie] rated operational current | AC-12: 4 A AC 440 V AC-12: 5 A AC 380/415 V AC-12: 8 A AC 110 V AC-12: 8 A AC 220/240 V AC-12: 8 A AC 24 V AC-12: 8 A AC 48 V AC-13: 6 A AC 110 V AC-13: 6 A AC 220/240 V AC-13: 7 A AC 24 V AC-13: 7 A AC 48 V AC-14: 4 A AC 110 V AC-14: 4 A AC 220/240 V AC-14: 5 A AC 24 V AC-14: 5 A AC 48 V AC-15: 3 A AC 220/240 V AC-15: 4 A AC 110 V AC-15: 5 A AC 24 V AC-15: 5 A AC 48 V DC-12: 0.4 A DC 250 V DC-12: 0.6 A DC 110 V DC-12: 2 A DC 48 V DC-12: 8 A DC 24 V DC-13: 2 A AC 24 V |
| Product compatibility | Compact NS630b…1600 Compact NSX100…250 Compact NSX400…630 |
| Standards | IEC 947-5-1 |
|---|---|
| IP degree of protection | IP20 connectors: conforming to EN 60529 IP40 front: conforming to EN 60529 IP30 side: conforming to EN 60529 |
| IK degree of protection | Front: IK07 conforming to EN 50102 |
| Unit Type of Package 1 | PCE |
|---|---|
| Number of Units in Package 1 | 1 |
| Package 1 Height | 27.000 cm |
| Package 1 Width | 28.000 cm |
| Package 1 Length | 38.000 cm |
| Package 1 Weight | 4.155 kg |
| Unit Type of Package 2 | P12 |
| Number of Units in Package 2 | 8 |
| Package 2 Height | 45.000 cm |
| Package 2 Width | 80.000 cm |
| Package 2 Length | 120.000 cm |
| Package 2 Weight | 48.600 kg |
| Warranty | 18 months |
|---|
